Elo TouchSystems E221 Manuel télécharger pdf (Page 77)

B-82 IntelliTouch/SecureTouch Guide

Jumper Settings

The following applies to 2210 and 2201 controllers only. Jumper blocks may

have a horizontal or vertical orientation, as shown in Figure B.1 on page B-82.

The figure shows jumpers installed normally for J3 and J7. Because some

jumpers work in tandem with others, a cross-connection may also be

significant. A valid cross-connection is shown between J0 and J1. Jumpers with

an invalid cross-connection, as with J4 and J5, have no effect and are available

as extra jumpers. To enable use of the jumpers, J7 must be installed. If J7 is not

installed, power-on settings are from NVRAM.

Figure B.1

SmartSet Controller Jumper Settings

1 2 ... 72 73 74 75 76 77 78 79 80 81 82 ... 106 107

AccuTouch 1
Trademark Acknowledgements 2
List of Figures 4
FCC Notice 8
UL Notice 8
Table of Contents 10
Index 105 11
NTRODUCTION 12
Driver Software 13
Shipping Damage 13
Care and Cleaning 14
Elo Entuitive Touchmonitor 15
OUCHMONITOR 16
NSTALLATION 16
Touchmonitor Configurations 17
• 2210MX serial controller 17
• 2201 PC-Bus controller 17
Touchmonitor Connections 17
Contents 18
Installation 18
Figure 3.2 21
PC-Bus Controller 22
Touchscreen Application Tips 23
Where to Go from Here 25
OMPONENT 26
Safety Information 27
Work Area 27
Protective Clothing 27
Getting Started 28
Figure 4.1 28
Bezel Design 29
Installation Steps 30
Suggested Tools 30
Disassembling the Display 31
Removing the Back Case 31
Discharging the CRT 32
Removing the CRT 34
Installing the Touchscreen 35
Figure 4.3 37
Transient Protection 41
Figure 4.4 42
Controller Interface Options 42
Internal Controllers 43
Figure 4.5 43
External Controllers 48
Reassembling the Monitor 52
Sealing the Monitor 53
ROUBLESHOOTING 56
Display Problems 57
Software Troubleshooting 57
Video Alignment Problems 58
Hardware Troubleshooting 58
Touchscreen Diagnosis 60
1-2, 4-5 (H-X, Y-L) 61
1-4, 2-5 (H-Y, X-L) 61
Touchscreen Simulation 62
Figure A.1 63
Serial Controller 64
Using the COMDUMP Utility 64
Byte Description 65
Byte MSB LSB 65
Using the TOUCHES Utility 66
RS-232 Connections 66
9 7 5 3 1 67
10 8 6 4 2 67
Power Supply 68
Figure A.2 68
Bus Controller 69
Using the BUSSTAT Utility 69
Touchscreen Cables 70
Figure A.3 71
Transient Protection Circuit 71
Diagnostic LEDs 71
2210 Serial Controller 71
3000U USB Controller 72
2201 PC-Bus Controller 72
LED Blink Rate Function 72
LED State Function 72
Diagnostic Codes 73
Bit Value (hex) Description 73
Figure A.4 74
ONTROLLER 76
ONFIGURATION 76
Jumper Settings 77
Figure B.1 77
Figure B.2 78
E271-2210 Serial Controller 78
2201PC-Bus Controller 80
2201Emulation Modes 82
(From Top) 82
Emulation Mode 82
PECIFICATIONS 84
Dust Seal 86
Watertight Seal 86
Light Transmission 87
Environmental 88
Temperature/Humidity 88
Temperature 88
Electrical 89
Agency Approvals 90
CE Compliance 91
OUCHSCREENS 94
The AccuTouch Touchscreen 95
Figure 2.1 95
AccuTouch Touchscreen 95
The AccuTouch Controllers 97
Glossary-99 98
standard 99
Glossary-101 100
Glossary-103 102
Numerics 104

Commentaires sur ces manuels

Pas de commentaire

Elo TouchSystems E221 Manuel Page 77

Commentaires sur ces manuels

Produits connexes et manuels pour Moniteurs à écran tactile Elo TouchSystems E221